Hybrid energy storage system integrating lithium-ion batteries and supercapacitors for enhanced electric vehicle performance

Ashiq Hussain; Muhammad Fasih Aamir

doi:10.59400/esc3933

Hybrid energy storage system integrating lithium-ion batteries and supercapacitors for enhanced electric vehicle performance

Ashiq Hussain
Graduate School of Science and Technology, University of Tsukuba, 1-1-1 Tennodai, Tsukuba 305-8577, Japan
Muhammad Fasih Aamir
Graduate School of Science and Technology, University of Tsukuba, 1-1-1 Tennodai, Tsukuba 305-8577, Japan

International Center for Materials Nanoarchitectonics (MANA), National Institute for Materials Science (NIMS), 1-1 Namiki, Tsukuba 305-0044, Japan

Article ID: 3933

Keywords: hybrid energy storage system (HESS), electric vehicles (EVs), supercapacitors, energy management system (ESS), battery management, Arduino control

Abstract

The increasing adoption of electric vehicles (EVs) has highlighted persistent challenges related to battery efficiency, limited lifespan and performance fluctuations during highly dynamic driving conditions. To address such issues, this study proposes a novel Hybrid Energy Storage System (HESS) that strategically combines lithium-ion batteries and supercapacitors to take advantage of the high energy density of batteries and the rapid charge-discharge characteristics of supercapacitors. The hybrid configuration is governed by an Arduino-based control unit equipped with an intelligent power management algorithm, which tracks real-time acceleration profiles and dynamically allocates power to the appropriate energy source. During steady-state operation, the batteries supply the required power, while peak loads during sudden acceleration or regenerative braking are effectively handled by the supercapacitors. Extensive simulations and laboratory experiments demonstrate that this strategy significantly reduces battery stress, mitigates thermal effects, and increases overall cycle life. Additionally, a dedicated mobile application enables real-time monitoring of key operating parameters, including SOC, vehicle speed and overall system status, thereby improving user interaction and enabling proactive maintenance decisions. Overall, the proposed HESS substantially improves energy efficiency and operational stability, representing a practical and scalable solution for achieving long-term sustainability and high performance in next-generation electric vehicle technologies.

Published

2025-12-08

How to Cite

Hussain, A., & Aamir, M. F. (2025). Hybrid energy storage system integrating lithium-ion batteries and supercapacitors for enhanced electric vehicle performance. Energy Storage and Conversion, 3(4). https://doi.org/10.59400/esc3933

Download Citation

Issue

Vol. 3 No. 4 (2025)

Section

Article

This work is licensed under a Creative Commons Attribution 4.0 International License.

References

[1]Bocklisch T. Hybrid energy storage systems for renewable energy applications. Energy Procedia. 2015; 73: 103–111.

[2]Hajiaghasi S, Salemnia A, Hamzeh M. Hybrid energy storage system for microgrids applications: A review. Journal of Energy Storage. 2019; 21: 543–570.

[3]Zhao S, Peng W, Zhou L, et al. Metal-organic cage crosslinked nanocomposites with enhanced high-temperature capacitive energy storage performance. Nature Communications. 2025; 16: 769.

[4]Chong LW, Wong YW, Rajkumar RK, et al. Hybrid energy storage systems and control strategies for stand-alone renewable energy power systems. Renewable and Sustainable Energy Reviews. 2016; 66: 174–189.

[5]Gao Z, Fang C, Gao Y, et al. Hybrid electromagnetic and moisture energy harvesting enabled by ionic diode films. Nature Communications. 2025; 16: 312.

[6]Hemmati R, Saboori H. Emergence of hybrid energy storage systems in renewable energy and transport applications–A review. Renewable and Sustainable Energy Reviews. 2016; 65: 11–23.

[7]Nkwanyana TB, Siti MW, Wang Z, et al. An assessment of hybrid-energy storage systems in the renewable environments. Journal of Energy Storage. 2023; 72: 108307.

[8]Bocklisch T. Hybrid energy storage approach for renewable energy applications. Journal of Energy Storage. 2016; 8: 311–319.

[9]Choi M-E, Kim S-W, Seo S-W. Energy management optimization in a battery/supercapacitor hybrid energy storage system. IEEE Transactions on Smart Grid. 2011; 3: 463–472.

[10]Fan Y, Qu W, Qiu H, et al. High entropy modulated quantum paraelectric perovskite for capacitive energy storage. Nature Communications. 2025; 16: 3818.

[11]Lukatskaya MR, Dunn B, Gogotsi Y. Multidimensional materials and device architectures for future hybrid energy storage. Nature Communications. 2016; 7: 12647.

[12]Cao J, Emadi A. A new battery/ultracapacitor hybrid energy storage system for electric, hybrid, and plug-in hybrid electric vehicles. IEEE Transactions on Power Electronics. 2011; 27: 122–132.

[13]Wang S, Wang S, Wei Z, et al. A parts-per-million scale electrolyte additive for durable aqueous zinc batteries. Nature Communications. 2025; 16: 1800.

[14]Ma H, Chen H, Chen M, et al. Biomimetic and biodegradable separator with high modulus and large ionic conductivity enables dendrite-free zinc-ion batteries. Nature Communications. 2025; 16: 1014.

[15]Song Z, Hofmann H, Li J, et al. Energy management strategies comparison for electric vehicles with hybrid energy storage system. Applied Energy. 2014; 134: 321–331.

[16]Tummuru NR, Mishra MK, Srinivas S. Dynamic energy management of renewable grid integrated hybrid energy storage system. IEEE Transactions on Industrial Electronics. 2015; 62: 7728–7737.

[17]Vosen S. Hybrid energy storage systems for stand-alone electric power systems: optimization of system performance and cost through control strategies. International Journal of Hydrogen Energy. 1999; 24: 1139–1156.

[18]Kumar K, Kwon S, Bae S. Deep reinforcement learning-based control strategy for integration of a hybrid energy storage system in microgrids. Journal of Energy Storage. 2025; 108: 114936.

[19]Emrani A, Berrada A. A comprehensive review on techno-economic assessment of hybrid energy storage systems integrated with renewable energy. Journal of Energy Storage. 2024; 84: 111010.

[20]Song Z, Hofmann H, Li J, et al. Optimization for a hybrid energy storage system in electric vehicles using dynamic programing approach. Applied Energy. 2015; 139: 151–162.

[21]Babu TS, Vasudevan KR, Ramachandaramurthy VK, et al. A comprehensive review of hybrid energy storage systems: Converter topologies, control strategies and future prospects. IEEE Access. 2020; 8: 148702–148721.

[22]Pan C, Fan H, Zhang R, et al. An improved multi-timescale coordinated control strategy for an integrated energy system with a hybrid energy storage system. Applied Energy. 2023; 343: 121137.

[23]Leon JI, Dominguez E, Wu L, et al. Hybrid energy storage systems: Concepts, advantages, and applications. IEEE Industrial Electronics Magazine. 2020; 15: 74–88.

[24]Kong L, Yan G, Hu K, et al. Electro-driven direct lithium extraction from geothermal brines to generate battery-grade lithium hydroxide. Nature Communications. 2025; 16: 806.

[25]Zhang Y, Jiang Z, Yu X. Control strategies for battery/supercapacitor hybrid energy storage systems. Publisher. 2008.

[26]Geetha A, Subramani C. A comprehensive review on energy management strategies of hybrid energy storage system for electric vehicles. International Journal of Energy Research. 2017; 41: 1817–1834.

[27]Liu H, Li C, Hu X, et al. Multi-modal framework for battery state of health evaluation using open-source electric vehicle data. Nature Communications. 2025; 16: 1137.

[28]Podder AK, Chakraborty O, Islam S, et al. Control strategies of different hybrid energy storage systems for electric vehicles applications. IEEE Access. 2021; 9: 51865–51895.

[29]Zheng C, Li W, Liang Q. An energy management strategy of hybrid energy storage systems for electric vehicle applications. IEEE Transactions on Sustainable Energy. 2018; 9: 1880–1888.

[30]Atawi IE, Al-Shetwi AQ, Magableh AM, et al. Recent advances in hybrid energy storage system integrated renewable power generation: Configuration, control, applications, and future directions. Batteries. 2022; 9: 29.

[31]Zhao P, Dai Y, Wang J. Design and thermodynamic analysis of a hybrid energy storage system based on A-CAES (adiabatic compressed air energy storage) and FESS (flywheel energy storage system) for wind power application. Energy. 2014; 70: 674–684.

[32]Adeyinka AM, Esan OC, Ijaola AO, et al. Advancements in hybrid energy storage systems for enhancing renewable energy-to-grid integration. Sustainable Energy Research. 2024; 11: 26.

[33]Sutikno T, Arsadiando W, Wangsupphaphol A, et al. A review of recent advances on hybrid energy storage system for solar photovoltaics power generation. IEEE Access. 2022; 10: 42346–42364.

[34]Lukic SM, Wirasingha SG, Rodriguez F, et al. Power management of an ultracapacitor/battery hybrid energy storage system in an HEV. In: Proceedings of the 2006 IEEE Vehicle Power and Propulsion Conference; 6–8 September 2006; Windsor, UK.

[35]Kim Y, Koh J, Xie Q, et al. A scalable and flexible hybrid energy storage system design and implementation. Journal of Power Sources. 2014; 255: 410–422.

[36]Wang Y, Song F, Ma Y, et al. Research on capacity planning and optimization of regional integrated energy system based on hybrid energy storage system. Applied Thermal Engineering. 2020; 180: 115834.

[37]Shen W, Zeng B, Zeng M. Multi-timescale rolling optimization dispatch method for integrated energy system with hybrid energy storage system. Energy. 2023; 283: 129006.

[38]Das DC, Roy A, Sinha N. GA based frequency controller for solar thermal–diesel–wind hybrid energy generation/energy storage system. International Journal of Electrical Power & Energy Systems. 2012; 43: 262–279.

[39]Pedram M, Chang N, Kim Y, et al. Hybrid electrical energy storage systems. In: Proceedings of the 16th ACM/IEEE International Symposium on Low Power Electronics and Design; 18–20 August 2010; Austin, TX, USA.

[40]Garcia F, Ferreira A, Pomilio J, et al. Control strategy for battery-ultracapacitor hybrid energy storage system. In: Proceedings of the 2009 Twenty-Fourth Annual IEEE Applied Power Electronics Conference and Exposition; 15–19 February 2009; Washington, DC, USA.

[41]Jing W, Lai CH, Wong WS, et al. A comprehensive study of battery-supercapacitor hybrid energy storage system for standalone PV power system in rural electrification. Applied Energy. 2018; 224: 340–356.

[42]Xiong R, Chen H, Wang C, et al. Towards a smarter hybrid energy storage system based on battery and ultracapacitor—A critical review on topology and energy management. Journal of Cleaner Production. 2018; 202: 1228–1240.

[43]Al-Ghussain L, Ahmad AD, Abubaker AM, et al. An integrated photovoltaic/wind/biomass and hybrid energy storage systems towards 100% renewable energy microgrids in university campuses. Sustainable Energy Technologies and Assessments. 2021; 46: 101273.

[44]Aktas A, Erhan K, Ozdemir S, et al. Experimental investigation of a new smart energy management algorithm for a hybrid energy storage system in smart grid applications. Electric Power Systems Research. 2017; 144: 185–196.

[45]Balachander K, Kuppusamy S, Vijayakumar P, et al. Comparative study of hybrid photovoltaic-fuel cell system/hybrid wind-fuel cell system for smart grid distributed generation system. In: Proceedings of the 2012 International Conference on Emerging Trends in Science, Engineering and Technology (INCOSET); 13–14 December 2012; Tiruchirappalli, India.

[46]Zhang X, Wang Y, Lai X, et al. Ultrasound-based intelligent identification method for regions and defects of lithium-ion batteries using a random forest model. Journal of Energy Storage. 2025; 132: 117746.

[47]Wang Z, Feng Z, Hu C, et al. Enhancing battery performance under motor overload drive with a battery–supercapacitor hybrid energy storage system. Journal of Power Sources. 2025; 642: 236680.

[48]Fang Z, Shek JK, Sun W. A review of grid-connected hybrid energy storage systems: Sizing configurations, control strategies, and future directions. Journal of Energy Storage. 2025; 118: 116226.

[49]Zhang Y, Yuan C, Du X, et al. Capacity configuration of hybrid energy storage system for ocean renewables. Journal of Energy Storage. 2025; 116: 116090.

[50]Ma B, Li P-H. Optimal flexible power allocation energy management strategy for hybrid energy storage system with genetic algorithm based model predictive control. Energy. 2025; 324: 135958.

[51]Aruna P, Prabhu VV, Krishnakumar V, et al. Innovative optimization of hybrid energy storage systems for electric vehicles: Integrating FBPINN-SAO to enhance performance and efficiency. Journal of Energy Storage. 2025; 108: 115021.

[52]Soonmin H, Taghavi M. Solar Energy Development: Study Cases in Iran and Malaysia. International Journal of Engineering Trends and Technology. 2022; 70: 408–422. doi: 10.3126/kjse.v8i1.69268

[53]Taghavi M, Salarian H, Ghorbani B. Thermodynamic and exergy evaluation of a novel integrated hydrogen liquefaction structure using liquid air cold energy recovery, solid oxide fuel cell and photovoltaic panels. Journal of Cleaner Production. 2021; 320: 128821.

[54]Ebrahimi A, Ghorbani B, Taghavi M. Novel integrated structure consisting of CO2 capture cycle, heat pump unit, Kalina power, and ejector refrigeration systems for liquid CO2 storage using renewable energies. Energy Science & Engineering. 2022; 10: 3167–3188.

[55]Taghavi M, Lee CJ. Development of novel hydrogen liquefaction structures based on waste heat recovery in diffusion-absorption refrigeration and power generation units. Energy Conversion and Management. 2024; 302: 118056.

Editor-in-Chief

Prof. Xiaohu Yang

Xi'an Jiaotong University, China

eISSN

3029-2778

Publication Frequency

Quarterly

About the Publisher

Academic Publishing insists on taking academic exchange and publication as the main line, carrying out comprehensive management based on science and technology, and fully exploring excellent international publishing resources. Within 5 years, it will form a strategic framework and scale with science (S), technology (T), medicine (M), education (E), and humanities and arts (H) as the main publishing fields. Academic Publishing is headquartered in Singapore and based in Malaysia, with the United States and China providing the main scientific and academic resources. At the same time, it has established long-term good cooperative relations with other publishing companies, scientific research communities, and academic organizations in more than a dozen countries and regions. Academic Publishing uses English and Chinese as its main publishing languages, mainly publishing books, journals, and conference papers in print and online. The vast majority of publications follow the international open access policy, providing stable and long-term quality and professional publications. With the joint efforts of the expert team and our professional editorial team, our publications will gradually be indexed by international databases in stages to provide convenient and professional retrieval for various scholars. At the same time, manuscripts we accept will be subject to the peer review principle, and cutting-edge and innovative research articles will be preferentially accepted for peer reference and discussion. All kinds of our publications are welcome for peer to contribute, access, and download.

more

Volume Arrangement

2026

2025

2024

2023

Featured Articles

Nitrided Copper-Iron Composite Oxides Derived from Layered Double Hydroxides for Enhanced Carbon Dioxide Electroreduction to Methane and Formic Acid

The reduction of carbon dioxide to valuable chemical products is a promising solution to address carbon balance and energy issues. Herein, amorphous nitrided copper-iron oxides are prepared by gas-phase nitriding of Cu Fe-layered double hydroxide precursor s with urea as nitrogen source. Amorphous materials are more likely to generate defect vacancies during the reaction process, and these vacancies can function as active sites for catalytic reactions. Therefore, the obtained materials show high activity for CO 2 electroreduction to methane and formic acid, achieving a total Faraday efficiency of 74.7% at −0.7 V vs RHE and exhibiting a continuous 10 h durability in the H-cell. The uniformly distributed Cu + sites act as active sites by losing electrons to activate CO 2 . During the CO 2 electroreduction , CO 2 is converted to *COOH via proton-electron coupling, *COOH combines directly with a proton in solution to produce the HCOOH product, and the other part of *COOH undergoes a protonated dehydration process to form the *CHO intermediate which dehydrates again to form CH 4 . This study provides a new approach for designing CO 2 electroreduction catalysts.

AlZnO magnetron sputtered thin film for photovoltaic application

Aluminum zinc oxide (AZO) is a nontoxic and a low-cost material that finds application as a transparent conducting electrode in photovoltaic devices. In this study the (direct current) DC magnetron sputtering of AZO films is carried out at different deposition times of 5, 10, 15, 20 and 25 min’s at room temperature and it’s structural, optical, electrical and morphological properties are studied for its use as a front contact for thin film solar cell application. The structural study suggests that the preferred orientation of grains along (002) plane having hexagonal structure and the optical and the electrical studies suggest that the films show an average transmission of 70% and a resistivity of the order of 10 -4 Ωcm. On the other hand, the scanning electron microscopy (SEM) images suggest the formation of packed grains having a homogeneous surface. Moreover in order to study the optoelectronic properties of prepared samples, the electronic and optical calculations of the AZO are performed by the first-principles calculations using density functional theory (DFT).

Investigation of self-excited induction generator for supporting domestic loads and its extension to a microgrid

This study provides a technical and financial analysis for the incorporation of a microgrid structure with a wind energy conversion system for producing electricity. This study’s primary aim is to provide solutions for issues that arise when isolated induction generators are employed with microgrids. A closed-loop smart electronic load controller is used to regulate the loads in the system that are supplied by the generation. A switched variable capacitor bank is used to supply reactive power initially during a voltage dip at varying winds and loads to sustain the voltage profile. Additionally, a simple voltage control loop-based controller for the generator side converter maintains the voltage at a steady level. Using HOMER software, an economic study of the suggested wind-based microgrid structure is also presented. A laboratory experimental setup is used to support the MATLAB/Simulink study of the proposed method and its control. The findings back the feasibility of implementing the suggested plan in grid-isolated regions for supplying critical loads.

Research progress on ZnO/MoS₂/rGO ternary photocatalysts

Energy shortage and environmental pollution have become one of the important global issues, and semiconductor photocatalytic technology is considered as one of the effective means to solve these problems. As a new and efficient green material, ZnO has attracted wide attention. ZnO is widely used in the field of photocatalysis due to its non-toxicity, low cost, environmental friendliness, adjustable band gap, high electron density, and chemical stability. However, the recombination of photogenerated charge carriers in ZnO hinders its practical application and lowers the utilization efficiency of visible light. On the other hand, molybdenum disulfide/reduced graphene oxide (MoS₂ /rGO), as a binary non-precious metal co-catalyst, has a larger specific surface area, suitable band gap width, and visible light response capability compared to single-phase graphene co-catalyst. Therefore, introducing MoS₂ /rGO co-catalyst into the ZnO system can provide more active sites, reduce the probability of photogenerated charge carrier recombination, and improve the utilization efficiency of visible light. In this review, we summarize the hydrothermal synthesis methods for preparing this highly demanded nanocomposite material, including one-step and stepwise methods. Subsequently, we elaborate on the mechanism of enhancing light absorption and achieving efficient electron-hole separation behavior in the ternary system heterojunction structure during the photocatalytic process. Due to its significant advantages, this ternary system heterojunction structure has been widely applied in the field of photocatalysis, including applications such as pollutant degradation, sterilization, and water splitting.

Wind power forecasting technologies: A review

This study addresses the critical role of wind power forecasting in ensuring stable and reliable power system operations. Wind Power Forecasting is critical for the efficient operation of plant, time scheduling, and it’s balancing of power generation with grid integration systems. Due to its dependency on dynamic climatic conditions and associated factors, accurate wind power forecasting is challenging. The research delves into various aspects, including input data, input selection techniques, data pre-processing, and forecasting methods, with the aim of motivating researchers to design highly efficient online/offline models on weather-based data. The overarching goal is to enhance the reliability and stability of power systems while optimizing energy resource utilization. The analysis reveals that hybrid models offer more accurate results, highlighting their significance in the current era. This study investigates different Wind Power Forecasting (WPF) models from existing literature, focusing on input variables, time horizons, climatic conditions, pre-processing techniques, and sample sizes that affect model accuracy. It covers statistical models like ARMA and ARIMA, along with AI techniques including Deep Learning (DL), Machine Learning (ML), and neural networks, to estimate wind power.

fmos